Howdy. Has anybody reloaded nickle brass. Do you have to do anything different with it compared to regular brass i thought i might try some its perrty Thanx

Hello Joe,

I give nickel cases a wide berth. I don't think it's as pliable as brass. Yeah, you're right, it is pretty but has been known to scratch hell out of the insides of your reloading dies. The most difficulty I've encountered is when bevelling the case necks before seating bullets. It will dull the bevelling tool in short order. I recently had to send two of them back to RCBS for re-sharpening because I had used them on nicekel brass, and they dulled my bevelling tools badly. Just one mans opinion. Best wishes.

Cal - Montreal

I agree with Cal, I will never fool with nickle brass again. I was preparing them in the usual way and while turning the necks, they ruined my cutter screw. They did get turned, but afterward they weren't so "purty" anymore anyway (cut most of the nickle off one side of the necks). I've got enough brass without using them.

Blaine

I have adn still use Nickle Plated Brass but I only use it for "Special" Loads. Due to the nature of the plated cases they are hard on any cutting tools, look terrible if you outside turn your necks and if for any reason a small piece of the plating comes off your dies will provide the remainder of all your cases with a reminder that you used plated brass.
Big Scratches!
I use the plated cases for my hunting ammo in some of my Contender loads and only with one brand & weight of bullet so I can tell at a glance the proper ammo has been packed for the trip. That's my use of Plated brass, P.S. Ensure that your Plated brass is squeeky clean prior to any loading. Flint54

Maybe i will stick to the regular brass thanx for the tips

I have used Nickel Brass in my .300 wby mag. All I did was neck size and load. I think the nickel finish with some lube on it is more slippery in the dies. Next time I will try a full resize and trim/bevel.

The only cases I've ever got stuck in my dies were nickel. I don't know about anyone else but I ended up using more lube than normal. Just was not that crazy about them.

If you use leather loops on your belt for rifle or revolver shells you might want to load Nickle plated brass. If you are out in the eliments for any length of time you might appreciate plated brass.

Nickel Brass...Looks pretty, but, in rifle calibers problem #1 is inside the neck, very Rough, so the bullets get scraped up inside the neck.
Bench shooters don't use nickel brass.

I have a selection of Speer nickle plated .30-06 cases that I use in inclement weather or long stays in the mountains. Never noticed any roughness or burring in the mouth of these cases. Of course I have used a camphuring tool in them when I first got them. Little magnum you might try the same thing. The nickled brass in no different then regular brass cases except they may not last as long, but if you have to keep them in leather for any time at all you better keep a few around. I have some Remington-Peters nickle plated brass that I bought in 1966 when I bought my .357 magnum Colt SAA that I am still using to this day. Granted that out of about 600 cases I only have around 150 left of that group, but I have not seen that much difference in life span between brass or nickled brass. At least not much...

Bushmaster...I will disagree that Nickel Brass is the same as brass. Nickel brass is plated brass. In rifle calibers I have used both Federal & Remmington Nickel brass with the same result, that after sizing and trimming, inside the case neck was not smooth as I would like, At first I thought it was my case trimmer or my die's. I will still load some Nickel brass, only because I have some, I just don't recommend the brass for top accuracy reloading.

I really don't understand your problem with nickle plated brass or everyone elses for that matter. I also have some Federal nickle plated brass and they have no burrs in them and they shoot well. I have loaded both the Speer and the Federals several times. Granted...They may not have as long of a life as plain brass, but they are handy for those bad weather hunts and long term in leather loops. I'm a bit old fasioned when it comes to my belts and other items that they have replaced with synthetics. I much prefer Leather goods. Cartridge belts, cartridge holders, holsters, Head stalls, reigns, saddle bags and saddles. As long as I use leather I will keep nickled brass handy for those ocassions.