View previous topic :: View next topic |
Author |
Message |
slimjim Super Member
Joined: May 16, 2009 Posts: 8314 Location: Fort Worth TX
|
Posted: Mon Jul 12, 2010 7:07 pm Post subject: Re: AR Thread!! |
|
fnuser wrote: |
So if I swap uppers for an optics ready half, would you go flat top; or one of the elevated optic platforms that allow use of standard high rings? |
I don't believe you loose any rigidity by going with a standard flat top. Many of the extra high rings are very strong (page 2 of this topic). I'm shooting 1" groups at 250 yards with consistent POI. Even with the very inexpensive rings, I've shot 100s of rounds in fast shooting competitions with no loose screws of change of POI. If you go for the elevated optics platforms to use standard rings, you loose the option/benefit of all the AR specific scopes and back-up sights. Plus I haven't seen many standard scopes that can fit on an AR without some sort of extention forward (bottom of page 2). Now that I say that, I haven't seen and AR with an elevated optics platform as an integral part of the AR upper except in on-line catalogs. I've never seen one at the range.
Last edited by slimjim on Thu Feb 03, 2011 5:23 am; edited 1 time in total |
|
Back to top |
|
|
slimjim Super Member
Joined: May 16, 2009 Posts: 8314 Location: Fort Worth TX
|
Posted: Mon Jul 12, 2010 7:18 pm Post subject: Re: AR Thread!! |
|
fnuser wrote: |
The other thing that nags my thoughts is the 6-223 is it worth it or would a tight twist 223 upper get you the same thing from a heavier .223 bullet, maybe a vld? |
I assume 6-223 is a 1:6 twist (<1:7) needed to stabilize 90gr VLD bullets. I have no experience with this set-up but have listened to others who have. First, bullets heavier than 80gr are too long to fit in the AR magazine thus 90gr must be fired single-shot. I also have heard that getting the 90gr to stabilize is not always a sure thing.
|
|
Back to top |
|
|
slimjim Super Member
Joined: May 16, 2009 Posts: 8314 Location: Fort Worth TX
|
Posted: Mon Jul 12, 2010 7:19 pm Post subject: Re: AR Thread!! |
|
Dallan, it would be nice if we could have posts with a number designator and be able to linnk with them.
_________________ "To anger a conservative, lie to him. To anger a liberal, tell him the truth." - Theodore Roosevelt
"The world is a dangerous place to live; not because of the people who are evil, but because of the people who don't do anything about it." - Albert Einstein |
|
Back to top |
|
|
fnuser Super Member
Joined: Dec 23, 2008 Posts: 914 Location: S.W. Missouri, U.S.A.
|
Posted: Tue Jul 13, 2010 4:32 pm Post subject: Re: AR Thread!! |
|
no I was thinking between 75-80g's I meant a vld 224 of a heavier weight, sorry not so clearI have another idea but it is still too early to publish.
_________________ N.R.A. Endowment Member |
|
Back to top |
|
|
slimjim Super Member
Joined: May 16, 2009 Posts: 8314 Location: Fort Worth TX
|
Posted: Tue Jul 13, 2010 7:46 pm Post subject: Re: AR Thread!! |
|
ideas!?! I love ideas! Bring them on or start a dedicated thread (that way you can delete it if it goes south).
_________________ "To anger a conservative, lie to him. To anger a liberal, tell him the truth." - Theodore Roosevelt
"The world is a dangerous place to live; not because of the people who are evil, but because of the people who don't do anything about it." - Albert Einstein |
|
Back to top |
|
|
slimjim Super Member
Joined: May 16, 2009 Posts: 8314 Location: Fort Worth TX
|
Posted: Mon Sep 13, 2010 4:15 pm Post subject: Re: AR Thread!! |
|
Well I finally got moving on my 2nd AR. At the end of last year I bought a lower receiver and parts but have been debating and waffling on which upper to get and in which cartridge. I was going for a wildcat like a 6.5mmBRX or 6mmDTI (6.8 SPC necked down with blown out shoulder). Finally just got tired of it all and went for a 24-inch Varmint Upper from Rock River. Should be here in a week or two. Meanwhile I assembled my lower. I still have to get anti-rotation pins for the trigger group so haven't installed them yet. I may go for an aftermarket single-stage trigger but don't need it right away.
Description: |
|
Filesize: |
52.28 KB |
Viewed: |
7487 Time(s) |
|
Last edited by slimjim on Thu Sep 16, 2010 6:22 pm; edited 1 time in total |
|
Back to top |
|
|
fnuser Super Member
Joined: Dec 23, 2008 Posts: 914 Location: S.W. Missouri, U.S.A.
|
Posted: Thu Sep 16, 2010 5:47 pm Post subject: Re: AR Thread!! |
|
I wish you would have collapsed that buttstock so I wouldn't have to scroll so much, Just kidding nice lower.
_________________ N.R.A. Endowment Member |
|
Back to top |
|
|
slimjim Super Member
Joined: May 16, 2009 Posts: 8314 Location: Fort Worth TX
|
Posted: Thu Sep 16, 2010 6:14 pm Post subject: Re: AR Thread!! |
|
fnuser wrote: |
I wish you would have collapsed that buttstock so I wouldn't have to scroll so much, Just kidding nice lower. |
I guess you are glad I didn't have the upper installed!
|
|
Back to top |
|
|
slimjim Super Member
Joined: May 16, 2009 Posts: 8314 Location: Fort Worth TX
|
Posted: Thu Sep 16, 2010 6:20 pm Post subject: Re: AR Thread!! |
|
I removed the spur from the hammer today to reduce lock time on my new build. A hacksaw didn't scratch the surface. Had to use a high-speed abrasive wheel. I'm not going remove the spur on my S&W M&P because I plan to shoot military ammo through it and may need the extra mass to initiate the mil primers. Also added KNS 2nd Gen anti-rotation pins. Almost everyone tells me I don't need them. However, I've seen what rotating pins can do to a steel receiver with my old rolling block. I don't want any wear on my AR lower receiver.
www.midwayusa.com/view...ber=581214
Description: |
|
Filesize: |
69.07 KB |
Viewed: |
7488 Time(s) |
|
Last edited by slimjim on Thu Sep 16, 2010 6:24 pm; edited 1 time in total |
|
Back to top |
|
|
slimjim Super Member
Joined: May 16, 2009 Posts: 8314 Location: Fort Worth TX
|
Posted: Thu Sep 16, 2010 6:23 pm Post subject: Re: AR Thread!! |
|
there fnuser - I collapsed the stock!
_________________ "To anger a conservative, lie to him. To anger a liberal, tell him the truth." - Theodore Roosevelt
"The world is a dangerous place to live; not because of the people who are evil, but because of the people who don't do anything about it." - Albert Einstein |
|
Back to top |
|
|
shrpshtrjoe Super Red Neck Member
Joined: Jan 26, 2005 Posts: 2965 Location: Maryland
|
Posted: Wed Feb 02, 2011 4:39 pm Post subject: Re: AR Thread!! |
|
I have bin changing around my AR Lately. I got rid of my Colt in the Fall to get my 4 wheeler and have missed not having a carbine So I sold my RRA upper and just bought a Spikes Tactical M4LE upper with a 1/7 twist . The 1/7 should do just fine with the 62grn or 70 grn TSX for deer. I should get the best of both worlds with this set up. I mounted a 2-7 Leupold on the PEPR mount and I think I'm going to buy a Burris fast fire 11 reflex sight and mount it on the picatinny ring top. . I will have a close range tactical sight and a long range sight without changing anything.. I will post some pics in a bit..
_________________ "MOLON LABE"
P E T A
People Eating Tasty Animals |
|
Back to top |
|
|
shrpshtrjoe Super Red Neck Member
Joined: Jan 26, 2005 Posts: 2965 Location: Maryland
|
Posted: Wed Feb 02, 2011 5:03 pm Post subject: Re: AR Thread!! |
|
Here's a couple pics of it so far
Description: |
|
Filesize: |
121.88 KB |
Viewed: |
7237 Time(s) |
|
Description: |
|
Filesize: |
148.32 KB |
Viewed: |
7237 Time(s) |
|
_________________ "MOLON LABE"
P E T A
People Eating Tasty Animals |
|
Back to top |
|
|
Elvis Super Member
Joined: Jul 27, 2008 Posts: 9239 Location: south island New Zealand
|
Posted: Wed Feb 02, 2011 7:28 pm Post subject: Re: AR Thread!! |
|
that sure looks naaasty.
_________________ You shot it You pluck it !
Them who eats the most duck eats the most feathers! |
|
Back to top |
|
|
slimjim Super Member
Joined: May 16, 2009 Posts: 8314 Location: Fort Worth TX
|
Posted: Wed Feb 02, 2011 7:52 pm Post subject: Re: AR Thread!! |
|
shrpshtrjoe, how do you like that foregrip? Are you using it in only tactical matches or while hunting, too?
_________________ "To anger a conservative, lie to him. To anger a liberal, tell him the truth." - Theodore Roosevelt
"The world is a dangerous place to live; not because of the people who are evil, but because of the people who don't do anything about it." - Albert Einstein |
|
Back to top |
|
|
shrpshtrjoe Super Red Neck Member
Joined: Jan 26, 2005 Posts: 2965 Location: Maryland
|
Posted: Thu Feb 03, 2011 5:11 am Post subject: Re: AR Thread!! |
|
slimjim wrote: |
shrpshtrjoe, how do you like that foregrip? Are you using it in only tactical matches or while hunting, too? |
I just put on and haven't shot with it yet but I was planning on using it all the time it has a good feel to it .
_________________ "MOLON LABE"
P E T A
People Eating Tasty Animals |
|
Back to top |
|
|
|