Reloading 2006

farrier · Member Joined: Jan 17, 2006 Posts: 43

I bought one of the RCBS Reloading kits and I love mine. It came with the Rock chucker supreme loading press, a good scale, speer loading manual, RCBS hand primer, case lube kit, loading block and some other stuff that I can't remember. I ordered mine for www.midwayusa.com they had the best price at the time. I recommend it for anyone wanting to start out with a good setup.

Dimitri · Super Member Joined: Nov 25, 2005 Posts: 5944

Thanks for the reply Smile

I'm thinking of possibly getting the RCBS turret press if I do have enough money at the time :).

Reason being is I could set up all the dies and not worry about installing them and reinstalling them and not setting them up right after Very Happy

As for dies I'm thinking about going with Lee. Smile

Dimitri

1895ss · Posted: Fri Jan 20, 2006 4:41 pm Post subject: Re: Reloading 2006

I've had my RCBS Rock Chucker press for more than 25 yrs and never a problem. I use mostly RCBS dies but also have some Lyman and one set of Lee dies. They all work just fine with non working better then the other. Like Jack said, start with a kit, that's the best way. I didn't but I'm not sure if they had kits back then. Smile

shrpshtrjoe · Posted: Fri Jan 20, 2006 4:50 pm Post subject: Re: Reloading 2006

Those RCBS RockChuckers are hard to beat I have had mine for 20+ years and it's still goin strong I wouldn't have any other Very Happy

Joe

Bushmaster · Posted: Fri Jan 20, 2006 6:50 pm Post subject: Re: Reloading 2006

coyote_Hunter_...You might look a 32 to 33 grains of W-748 with those 170 grain Speer FNs in .30-30. (Warning: These loads are at or over recommended charges for this powder. Work up slowly and with care). I use a CCI 200 primer in Winchester or Remington cases...

BigBlue · Posted: Fri Jan 20, 2006 7:05 pm Post subject: Re: Reloading 2006

My first post! Very Happy

Coyote Hunter,
I always had good luck using 37.0gr. of Hodgdon BL-C(2) with Speer 150 gr. bullets in my 30-30. This is a listed max load, but at a lower than modern standards pressure. It can be expanded on in modern lever guns, but the 37.0gr. has proved to be the most accurate for me.
Don

Dimitri · Super Member Joined: Nov 25, 2005 Posts: 5944

BigBlue,

Welcome to the forums stay a while and post offen Cheers

Dimitri

BigBlue · Posted: Fri Jan 20, 2006 7:11 pm Post subject: Re: Reloading 2006

Dimitri,
Thanks for the welcome. I was hunting for some 7mm Rem Mag loads when I stumbled onto this forum. I've been using Point Blank software for longer than I can remember. I found it at as a link from another forum quite a while back and really love it for setting up loads.
Don

Bushmaster · Posted: Fri Jan 20, 2006 7:19 pm Post subject: Re: Reloading 2006

And it is going to be up graded soon...At least that's what the "BOSS" says... Very Happy

Welcome to the site BigBlue...

DallanC · Site Admin Joined: Jan 18, 2005 Posts: 3572 Location: Utah

BigBlue wrote:

Dimitri,
Thanks for the welcome. I was hunting for some 7mm Rem Mag loads when I stumbled onto this forum. I've been using Point Blank software for longer than I can remember. I found it at as a link from another forum quite a while back and really love it for setting up loads.
Don

Welcome to the site.

As for PointBlank I am currently re-writing it fixing bugs and adding in new features. I'm happy with the initial results (using a new language for it than the original was written in) and it looks like it will be alot nicer. Lots more to do still though... but keep checking in for the status updates on it.

-DallanC

GroovyJack · Member Joined: May 21, 2005 Posts: 621 Location: Bama

SS nope we didnt have the kit luxury back them ..
Jack

BigBlue · Posted: Fri Jan 20, 2006 8:15 pm Post subject: Re: Reloading 2006

DallanC wrote:

Welcome to the site.

As for PointBlank I am currently re-writing it fixing bugs and adding in new features. I'm happy with the initial results (using a new language for it than the original was written in) and it looks like it will be alot nicer. Lots more to do still though... but keep checking in for the status updates on it.

-DallanC

DallanC,
I've judged the performance of a lot of loads from .223 to .500 S+W on that program. Many times I use it to decide on a cartridge or even a rifle. I often make little cheat sheets on masking tape and put them on my stock for ranges past the point blank range that I set my scope for.
It's long past time I said a personal thanks.
Don

SeniorCoot · Posted: Sat Jan 21, 2006 5:29 am Post subject: Re: Reloading 2006

Well we're getting off my topic BUT that's ok--Speaking of rock Chucks- i still use my buddies- he died in a freak hunting accudent just befroe we were going to leave AK to hunt in America in 92--it brings bacl good memories of times past every time i start up.
Going to try Accubonds pushed by H 4831- 54 gr to start- I think the powder and bullets guys are leary of putting out info on heavy loads because of out present societal penchant towards Suing everybody for every thing- i have 4 or 5 sources and each one is different for same powders/bullets/cal--Talking with Nosler guy last week he wasa very hesitant to give loads but i got them and some advice to boot.

farrier · Member Joined: Jan 17, 2006 Posts: 43

I have never used any dies other than RCBS, and don't get me wrong they work great, but I think that if I were to try something different I might try Hornady theirs has a plug in the seating die that slides up and down, that is suppose to make lining up the bullet with the case a little better, but I don't know.
Has anyone tried the Hornady dies, if so what do you think of them?
I just thought of one down fall for the RCBS dies, and that is I don't like their lock rings, I replace them with forester.

Bushmaster · Posted: Sat Jan 21, 2006 10:25 am Post subject: Re: Reloading 2006

Gee gosh SeniorCoot...I thought we covered it quite well...Hopefully we helped you decide to continue loading your old loads and that your #47 Lyman was mostly up to date except for the new powders and a very few new calibres...Least I thought so...?

Being a SeniorCoot you must have a lot to contribute to this forum...Us young( Very Happy

) guys may need your expertice. So keep talkin'... Cheers