#16: Re: Savage Model 110 Author: SHOOTER458, Posted: Sat Nov 05, 2005 8:56 am ---- I have 2 Savages, a 112 in 223 that will shoot most anything under 1/2 inch at a 100 and a 116 in 300RUM that will now shoot around 1". The 116 needed a little help, the recoil lug was about 1/16" from contacting the stock when new. Wouldnt shoot under 3"! A litle Accraglass and no more problems.
#17: Re: Savage Model 110 Author: shrpshtrjoe, Location: MarylandPosted: Sat Nov 05, 2005 9:02 am ---- Welcome aboard shooter458 I have a 12fv in 223 it shoots 1/2 moa as well.
#18: Re: Savage Model 110 Author: w4dsb, Location: Loganville GeorgiaPosted: Wed Nov 30, 2005 5:49 pm ---- glad i found this discussion, looking to order a 7mm 08 barrel for my 308 caliber savage 110. I know i need go-no go gauges and the barrel nut wrench anything else i need to watch out for? any advise would be deeply appreciated
#19: Re: Savage Model 110 Author: JO422, Posted: Wed Nov 30, 2005 7:17 pm ---- The Savages are excellent guns. I do not own one, but I have shot a couple that will easily shoot under 1/2 MOA if the shooter does his part. With the Accu-Trigger Savage does have the best trigger out of the box. Apparently Savage does not have a lawyer setting the trigger pulls for their rifles, as Remington and Winchester seem to have . Fortunately the Remingtons are easy to adjust, just don't send them back to the factory or they'll ding you for a new trigger before they return it to you .
I didn't know that Savages are that easy to convert to other calibers, I might have to get one and try it 8). I think Brownells has some barrels in stock for the Savge.
#20: Re: Savage Model 110 Author: BillPa, Posted: Wed Nov 30, 2005 11:20 pm ---- w4dsb,
The tools needed to do a barrel swap on a Savage are.....
1. A spanner wrench for the nut form SharpShooters Supply or Wheeler.
2. Barrel blocks / vise
3 Optional,but hightly recommended, an action wrench from Wheeler.
4. Go - no go gages.
If you going to the same class cartridge(243-308,etc) all you'll need is the barrel. If you going to something like a 308 from 223, you need a new bolthead,magazine and follower.
Pre-chambered/threaded barrels are avaible from Pac-Nor,A&B and Shaw.
Initally, removing the nut can be a problem. You may need to heat it a bit to break the thread sealant. 19" arms or a dead blow hammer are a plus!
Always use a stripped bolt to set the headspace on the go gage. You may need to readjust the headspace a bit after tightening the nuit since it has a tendancy to open it up somewhat. One tip...use a a piece of scotch tape under the bolthead pin to keep in in place while adjusting the headspace.
After you do one ot two its quite easy. I swap between 25-06,270,30-60 and 338-06 on one action. Another was a 22-250 now a 260 Rem.,a 22-250 and 22-250AI and I 'm waiting on a 250 AI to go on a Stevens 200 action,prevoiusly a 7-08.
A few other suggestions are a Sharp Shooter trigger and recoil lug.
Visit Savageshooters.com for a lot of additional information.
Hope this helps!!!
Bill
#21: Re: Savage Model 110 Author: w4dsb, Location: Loganville GeorgiaPosted: Thu Dec 01, 2005 3:28 pm ---- THANKS BillPa !
#22: Re: Savage Model 110 Author: happycamper, Posted: Fri Aug 03, 2007 1:09 pm ----
grimel wrote:
Umm, the $50 covers the go/no-go headspace gauges and the $15 wrench.
Hi
werer do you get a 15.00 wrench for the savage rifle
apple03 @ localnet.com
#23: Re: Savage Model 110 Author: BillPa, Posted: Sat Aug 04, 2007 6:32 am ---- WOW....I've changed my barrel swapping procedure a lot since 2005!
Today, I don't use a barrel vise/blocks at all anymore. Now, a clamp on action wrench, a spanner and a tossed together fixture for the factory installed barrels, a modified open ended spanner a rear entry wrench for everything else, without removing the scope or mount(s).
The collection is now up to 13 complete rifles, 8 spare barrels. Calibers run from a 22-250AI up to 338 Federal for the SAs, 25-06 to 300WM for the LAs. The last addition, a 14 AC, originally a 7-08, is now a 260. The next two in the works are a 250 Savage and 6-250AI.
Midway has the Wheeler action wrench and spanner on sale now, $45.99 and $19.99.
Bill
#24: Re: Savage Model 110 Author: centerfire, Posted: Wed Sep 03, 2008 5:38 pm ---- My ears hear good things about them Mod.12 in.223