HuntingNut
HuntingNut
   Login or Register
HomeCommunity ForumsPhoto AlbumsRegister
     
 

User Info

Welcome Anonymous


Membership:
Latest: RichardZ
New Today: 0
New Yesterday: 0
Overall: 13126

People Online:
Members: 0
Visitors: 205
BOT: 0
Total: 205
Who Is Where:
 Visitors:
01: Forums
02: Forums
03: Forums
04: Forums
05: Forums
06: Home
07: Forums
08: Your Account
09: Forums
10: Home
11: Forums
12: Forums
13: Home
14: Forums
15: Forums
16: Forums
17: Home
18: Home
19: Your Account
20: Home
21: Home
22: Home
23: Home
24: Your Account
25: Home
26: Home
27: Home
28: News
29: Your Account
30: Your Account
31: Your Account
32: Home
33: Your Account
34: Forums
35: Home
36: Forums
37: Home
38: Your Account
39: Forums
40: Forums
41: Your Account
42: Forums
43: Forums
44: Forums
45: Forums
46: Forums
47: Home
48: Forums
49: Forums
50: Forums
51: Home
52: Forums
53: Home
54: Forums
55: Forums
56: Forums
57: Forums
58: Forums
59: Forums
60: Home
61: Forums
62: Forums
63: Your Account
64: Forums
65: Forums
66: Home
67: Home
68: Forums
69: Your Account
70: Home
71: Photo Albums
72: Forums
73: Forums
74: Home
75: Forums
76: Home
77: Forums
78: Forums
79: Forums
80: Forums
81: Your Account
82: Home
83: Photo Albums
84: Forums
85: Forums
86: Your Account
87: Forums
88: Home
89: Members List
90: Forums
91: Your Account
92: Forums
93: Your Account
94: Home
95: Forums
96: Forums
97: Forums
98: Forums
99: Your Account
100: Your Account
101: Forums
102: Home
103: Forums
104: Your Account
105: Home
106: Photo Albums
107: Forums
108: Home
109: Forums
110: Forums
111: Forums
112: Photo Albums
113: Your Account
114: Your Account
115: Forums
116: Forums
117: Home
118: Home
119: Forums
120: Photo Albums
121: Home
122: Forums
123: Forums
124: Home
125: Home
126: Forums
127: Home
128: Home
129: Photo Albums
130: Forums
131: Forums
132: Forums
133: Forums
134: Forums
135: Your Account
136: Forums
137: Forums
138: Your Account
139: Forums
140: Forums
141: Forums
142: Forums
143: Your Account
144: Your Account
145: Your Account
146: Forums
147: Forums
148: Forums
149: Forums
150: Forums
151: Home
152: Forums
153: Forums
154: Forums
155: Forums
156: Forums
157: Your Account
158: Forums
159: Forums
160: Forums
161: Forums
162: Forums
163: Forums
164: Forums
165: Forums
166: News
167: Home
168: Forums
169: Forums
170: Forums
171: Forums
172: Photo Albums
173: Your Account
174: Forums
175: Forums
176: Home
177: Forums
178: Forums
179: Photo Albums
180: Photo Albums
181: Forums
182: Photo Albums
183: Home
184: Forums
185: Photo Albums
186: Forums
187: Your Account
188: Home
189: Photo Albums
190: Forums
191: Photo Albums
192: Forums
193: Forums
194: Home
195: Home
196: Forums
197: Photo Albums
198: Forums
199: Forums
200: Forums
201: Home
202: Forums
203: Forums
204: Forums
205: Home

Staff Online:

No staff members are online!
 

Coppermine Stats
Photo Albums
 Albums: 308
 Pictures: 2451
  · Views: 820725
  · Votes: 1316
  · Comments: 86
 

Marlins trigger pull
Discussions related to Guns and Firearms
Go to page 1, 2, 3  Next
View previous topic :: View next topic  
Author Message
squirrelbait
Member
Member


Joined: Sep 23, 2005
Posts: 220
Location: Nottingham, NH

PostPosted: Mon Feb 13, 2006 1:11 pm    Post subject: Marlins trigger pull Reply with quote

Has anyone ever had a problem with a Marlin carbine trigger pull?
I bought a new 1894c in December and have been trying to work up a good 357 load. The trigger seemed "real tight"! I just measured it with my fish scale at 10lbs. 10lbs!! In any event I have not gotten a call back from Marlin yet......I asked if it would be non-warrenty or warrenty to tweak it a little. Bushmaster, I know, I shoulda bought a good gun.....win94 Laughing but the Marlin has a little thicker (meatier forend) and feels better to me. What can I say.
Back to top
View user's profile
roklok
Super Member
Super Member


Joined: Aug 11, 2005
Posts: 608
Location: Fairbanks, Alaska

PostPosted: Mon Feb 13, 2006 8:37 pm    Post subject: Re: Marlins trigger pull Reply with quote

I have never tried one but Wild West guns offers replacement triggers for Marlins that they claim reduces pull weight to 2-3 pounds.Available from Midway.
Back to top
View user's profile
Bushmaster
Super Member
Super Member


Joined: Jun 12, 2005
Posts: 11390
Location: Ava, Missouri

PostPosted: Mon Feb 13, 2006 9:12 pm    Post subject: Re: Marlins trigger pull Reply with quote

Squirrelbait...I agree...You should have gotten a Winchester. But, be as it may, you have purchased a Marlin. Now pay the price...10 lbs does seem a bit much. You need to look into having a trigger job done or go with roklok's idea. I would be a bit careful about getting too light a trigger pull. A pull of 2 lbs or less is normally reserved for target pistols and rifles. Combat pulls are 2 lbs and up. I know what a 2 lb pull is on a Colt 1911. and it ain't much believe me. I have never checked the pull on my 1948 Winchester mod 94, it's light, but not in the 2 lb catigory and niether is my Browning .30-06. You might pressure the Marlin factory reminding them that you are a customer and might return to buy another of their products if they capitulate. Or you might do the "Bushmaster Thing"...Get mad and through a tantrum over the phone and remind them they could get a bad rap over this...Your choice...Call the Marlin people again and insist on an answer. It might be what they call a standard trigger pull. If so procede to the above suggestions...1895ss...What do you think of this or have you gotten used to a 10 lb pull... Very Happy

_________________
I have one nerve left and yer standin' on it...

DEMOCRACY Two wolves and one sheep voting on what to have for lunch...
LIBERTY A well armed sheep contesting the outcome of the vote...
Back to top
View user's profile
1895ss
Super Member
Super Member


Joined: Jul 21, 2005
Posts: 2612
Location: Not Here...!!

PostPosted: Mon Feb 13, 2006 9:36 pm    Post subject: Re: Marlins trigger pull Reply with quote

I do believe the main spring can be replaced by a lighter spring which eases up the cocking and trigger pull tension. My 1895ss action was tight and stiff when new. Gunsmiths can smooth it some but I did what many people have done with the Marlin lever and that was to sit and dry fire it (1000's of times) while doing some other activity. It made the action very smooth and my trigger pull, which was never that bad, is in the 4.5 - 5 lb range with a fish scale. If it new it has to be broke in.................

_________________
A cruel truth is much more desirable than a really nice lie.
'Tis far better to walk alone than to follow a crowd or an a**hole going the wrong way.
Back to top
View user's profile Send e-mail
Bushmaster
Super Member
Super Member


Joined: Jun 12, 2005
Posts: 11390
Location: Ava, Missouri

PostPosted: Mon Feb 13, 2006 9:42 pm    Post subject: Re: Marlins trigger pull Reply with quote

I would figure that a 4 to 5 lb pull would be just about right for a hunting rifle. anything less then that might be a problem in the woods...Premature let off (sounds sentual) or accidental let off (definately sexual). However, dangerous...

_________________
I have one nerve left and yer standin' on it...

DEMOCRACY Two wolves and one sheep voting on what to have for lunch...
LIBERTY A well armed sheep contesting the outcome of the vote...
Back to top
View user's profile
squirrelbait
Member
Member


Joined: Sep 23, 2005
Posts: 220
Location: Nottingham, NH

PostPosted: Tue Feb 14, 2006 6:40 am    Post subject: Re: Marlins trigger pull Reply with quote

Great inputs!
I was thinking about 3-4 or so. MY TC encore with same scale was just under 2 and I know (and the kids) that we have to be careful in the woods with it. A friend of mine suggested I don't take it to a local gunsmith......yet....... because it will void any warranty. I am with you Bushmaster, I tend to get pretty emotional over the phone, actually in the stores too. I have little patience for sales people and support people who seem to have no, zero that is........ common sense. This seems to becoming more and more frequent. (I'm finding my 100 acres and moving out)
I've got about 250 to 300 rounds thru this carbine and getting to 2 inch groups has been difficult. I now have a load that is looking like about 1.5 inches but need to test for consistency. I am feeling better about be able to get a good group......cause I think bring the trigger down will help.
Back to top
View user's profile
squirrelbait
Member
Member


Joined: Sep 23, 2005
Posts: 220
Location: Nottingham, NH

PostPosted: Tue Feb 14, 2006 9:31 am    Post subject: Re: Marlins trigger pull Reply with quote

Thanks to Dallan and the Huntingnut team. This is what makes forums, especially well organized, and dare I say some control, well worth while. Great bunch of participants and moderators.
thanks
Back to top
View user's profile
Coyote_Hunter_
Member
Member


Joined: Mar 05, 2005
Posts: 208
Location: Franktown, CO

PostPosted: Thu Feb 16, 2006 12:03 pm    Post subject: Re: Marlins trigger pull Reply with quote

The Marlin triggers are easy to reqork - I've done two of mine and the third got replaced by a Wild West Guns 'Happy Trigger'. The Happy Trigger is excellent but pricey.

_________________
Coyote Hunter
NRA, GOA, DAD
Back to top
View user's profile Photo Gallery
squirrelbait
Member
Member


Joined: Sep 23, 2005
Posts: 220
Location: Nottingham, NH

PostPosted: Thu Feb 16, 2006 1:10 pm    Post subject: Re: Marlins trigger pull Reply with quote

Coyote Hunter, looked em up. Cabella sells them. This looks like a great idea. Have to save some dollars up and try it. Thanks bunch. Oh, Marlin did get back to me and the rifle is off to the factory.....just to see what they do. Anything will be an improvement. Thanks again. This could be helpful to anyone else with a Marlin.
Back to top
View user's profile
Bushmaster
Super Member
Super Member


Joined: Jun 12, 2005
Posts: 11390
Location: Ava, Missouri

PostPosted: Thu Feb 16, 2006 7:09 pm    Post subject: Re: Marlins trigger pull Reply with quote

Nope...I don't own one...

_________________
I have one nerve left and yer standin' on it...

DEMOCRACY Two wolves and one sheep voting on what to have for lunch...
LIBERTY A well armed sheep contesting the outcome of the vote...
Back to top
View user's profile
515034s10ring
Super Member
Super Member


Joined: Sep 08, 2005
Posts: 1153
Location: Working my way back up and around

PostPosted: Thu Feb 16, 2006 7:16 pm    Post subject: Re: Marlins trigger pull Reply with quote

10 pounds just sounds down right nasty for a trigger Shocked . Changing springs and having stone work done is pretty much your only option and that will cost no less than $50 from a reputable smith.

_________________
Why no......I'm really not an outdoorsmsn at all. But i did stay in a Holiday Inn Express last night!
Back to top
View user's profile
1895ss
Super Member
Super Member


Joined: Jul 21, 2005
Posts: 2612
Location: Not Here...!!

PostPosted: Sun Mar 12, 2006 5:10 pm    Post subject: Re: Marlins trigger pull Reply with quote

squirrelbait, did you fix your trigger pull problem..... ? If not here is some info that i found some time ago but missplaced it and couldn't find it back when you first asked this question. I have never had to do this but here it is.......






The following procedures apply to the Models 1894, 1895 and the 336.
TOOLS AND EQUIPMENT
Before you attempt to do any work on your rifle, get a good set of gunsmith screwdrivers. Do not try to use your hardware store special screwdrivers. Burred screw heads will result from use of standard screwdrivers. Gunsmith screwdrivers are available from Lyman, Chapman and others. If not available locally, gunsmith screwdrivers can be ordered from Midway, Brownell's and others.
Additional equipment required will consist of a sheet each of 400 and 600 grit wet or dry paper. Nice to have would be a few small hones, but the wet or dry paper will get you by. When begining to work on the hammer, a belt sander or bench grinder will be required for part of the procedure.
INSPECTION
Before beginning with the actual tune up, cycle the action slowly and try to determine where in the cycle roughness is felt. The areas to pay attention to are the lever plunger that holds the lever closed, the carrier lifting up, the bolt sliding in the receiver and the bolt passing over the hammer. All of these areas will most likely require attention and will be addressed during the tune up. Unless you have been shooting your rifle a great deal, It is recommend that you cycle the lever several hundred times prior to beginning any work. This will accomplish two things. First, it may smooth out any burrs that are there. Second, it will leave burnish marks on the areas that are in contact so you can identify those areas needing work. If you reload, make up several dummy rounds, without primer. Cycle these dummy rounds through the action. By doing so, you may find areas inside the action where brass has rubbed off on the parts. This will give you an excellent idea of where to spend time polishing those parts. Before disassembly, slowly open the action and observe the point at which the hammer comes to full cock. On some Marlin 1894 and 1895, the bolt depressed the hammer another 3/32" after reaching full cock. We will address this when we work on the hammer.
DISSASEMBLY
Begin disassembly by opening the action about half way and remove the lever screw, the lever, the bolt and the ejector. Remove the rear tang screw and slide the stock of the rear off the action. Lower the hammer by depressing the trigger safety block. Hold the hammer under the thumb, depress the trigger and let the hammer go forward against the frame. Remove the hammer spring by sliding the hammer spring plate to the left side and then remove the hammer spring. Remove the hammer pivot screw and remove the hammer through the clearance slot by rotating it upward. Turn the rifle over and remove the trigger guard plate support screw from the left side of the action. Then remove the trigger guard plate screw from the bottom. This is the screw just in front of the carrier leg slot. Note that this screw is longer than the previous screw. Lift up on the lower tang and remove the trigger guard plate. Remove the locking bolt from the bottom of the action. Remove the carrier screw from the right side of the action. The carrier will now fall out of the bottom of the action. There is no need to remove the loading gate screw. The action is now dissembled as far as required for the tune up.
LEVER
Inspect the lever for any burrs on the end where it bears on the carrier and bolt. Burnish marks on the end will show where it is in contact with the carrier and bolt. Lay a 2" by 2" piece of 400 grit wet or dry paper on a flat surface near the edge of your workbench. Place one side of the lever flat on the paper and polish the side. Then flip it over and polish the other side. Polish off any burrs found on the two narrow edges. Stay clear of any of the areas that will be outside of the action so that you don't remove any bluing. This is a polish only operation. Do not remove metal or change the shape of the end of the lever.
The finger lever plunger will need to be polished and the spring tension reduced. With a small punch or nail with the end ground flat, remove the plunger pin. The plunger is under tension, so be careful and don't let the plunger and spring jump out and get lost. Hold a finger over the plunger end or put a small rag over it to contain it. Using the 400 and 600-grit paper, polish the two bevels on the end of the plunger. Check the shank of the plunger and remove any burrs you may find. Place the spring back on the plunger and insert it into the hole in the lever. While looking through the pin hole, push the plunger in until the hole is clear. Continue pushing in the plunger until it is flush or nearly so. This will give you a good idea of the amount of the spring that can be removed. In some rifles, the removal of two coils by cutting them off with a good pair of side cutters. It is recommend that you only cut one coil at a time and then try the plunger in the lever for tension. The plunger must have enough tension to fully extend and lock the lever in the closed position. If you remove too much of the spring, you may find that the lever will unlock when you fire the rifle with heavy recoiling loads. Since your fingers are through the lever when firing, this is not a dangerous occurrence. However, it is annoying.
TRIGGER GUARD ASSEMBLY
Unless you are experienced in working on sear surfaces, It is recommend that you leave the trigger and sear alone.
Take the trigger plate in your hand and look down into it from the top side. You will see the trigger block safety spring. This spring also bears on the rear of the trigger. Using a small screwdriver under the short leg, the one bearing on top of the trigger safety block, pry up on the spring approximately 1/8". You want to bend this leg upward enough to relieve tension on the trigger safety block. Don't try to get all the bend in one try, but bend it up a little, try the trigger block safety for tension by pushing it up from the bottom behind the trigger. Continue bending and trying until you can easily move the safety block up with your finger. Leave enough tension so that the safety block always returns to it's down position.
Now look at the long leg of the spring where it bears on the rear of the trigger. Pry it up a little at a time to relieve some tension on the trigger. Be careful and don't kink the spring. You are only trying to relieve some of the tension. It is better to error on the safe side rather than having to buy a new spring.
Some people feel that the floppy two-piece trigger/sear in the Marlin is undesirable. There are after market one-piece triggers available to replace the Marlin trigger. These replacement triggers are also advertised to reduce the trigger pull weight.
LOCKING BOLT
Check for any burrs and polish the sides and any burnished areas. Do not remove any metal or change the shape.
BREECH BOLT
Place the bolt back in the action and slowly slide it back and forth. It should move smoothly through out its length. Check for any burrs on the bolt and in the receiver and polish them out if you find any. Pay attention to the slot in the side of the bolt where the ejector rides and carefully polish the slot's sides and bottom. Wrapping a small piece of the 600-grit paper around a narrow file or Popsicle stick easily does this. Carefully polish the cam on the bottom of the bolt where it rides over the hammer nose. Do not reduce the height of the cam. Polish it only.
McPherson's gives detailed instruction on how to narrow this cam to reduce the friction as the bolt rides over the hammer. This modification is not for the faint of heart and should only be attempted by the advanced amateur or professional gunsmith. Bolts are not cheap should you have to replace it.
Like the objection to the two-piece trigger/sear, some object to the two-piece firing pin. Theory is that the two-piece pin requires more force from the hammer to fire the primer, especially when the hammer spring has been reduced. After market one-piece firing pins are also available. In his book, McPherson details how to modify the existing firing pin to lighten it.
HAMMER & HAMMER SPRING
Remove ¾ of a coil from each end of the hammer spring. If you use a grinder to do this, do not get the spring too hot to hold or allow the spring to change color. Go slowly and grind the cut off end flat like it was done at the factory. If you do not have a grinder, use a triangular file to file a groove in the coil and break the end off. Then file it flat. A Dremel tool with a cutoff blade will also work to remove the ¾ coil. In all three cases, do not nick the adjacent coil as this will set up a weak spot for future breakage. The hammer spring, due to its barrel shape, goes away very quickly. Should you remove too much, you will find that it will not reliably, maybe not at all, provide enough force to fire a primer. If this occurs, and you do not have a spare spring, do not despair. Locate, in your parts drawer or at the local hardware store, some small, thin washers that will just freely slip over the hammer strut. Place one on each of end of the spring and try to fire a primer in an empty case. One washer on each end will most likely provide enough power to fire a primer.
• Reduced force after market main springs are available for those who desire to purchase them rather than modifying the existing spring.
• Using the wet or dry paper, polish the hammer strut on both sides and both edges. Check and remove any burrs from the hammer pivot hole. Polish the hammer screw where the hammer pivots.
• Check the sides of the hammer for bright drag spots. A burr in the receiver rubbing against the hammer can slow the hammer fall. Remove any burrs.
Remember the 3/32" hammer over travel referred to above? Some of this can be removed by grinding the nose of the hammer down using a belt sander or fine grinding wheel. If you feel uneasy about removing metal from the hammer, skip this step. You need to remove approximately 1/32" (.031"). Filing the hammer nose is not practical due to radius and the requirement to maintain the exact contour. Carefully grind and polish the hammer nose. Removing more than 1/32" (.031") is not recommended. This will assure that the hammer is sufficiently depressed to be held at full cock. Scribe lines on both sides of the hammer nose following the same contour and remove metal to this line. A better method of assuring that you don't remove too much is to use a vernier caliper and measure from the flat on the bottom of the hammer to the nose. Go slowly, measure often and then polish the nose. Be advised that altering the hammer may void the manufacturer's warranty.
CARRIER ASSEMBLY
Leave the sides alone. Polish all burnished areas where the lever acts on the carrier. Look for brass colored areas where brass rubbed off and polish those areas as well. Check the screw hole for burrs and remove. Polish the screw where the carrier pivots.
EJECTOR
Check for burrs and polish as required. Polish the cam area where the bolt pushes the ejector down into its slot in the receiver. Spring tension on the ejector can be reduced by carefully bending the spring toward the ejector. Again, an after market one piece ejector/spring is available.
SAFETY
Everyone complains about the cross bolt safety. However, it does have a couple of good traits. One, it allows you to safely cycle rounds through the action to unload the magazine without the danger of an accidental discharge. Two, you can dry fire occasionally without danger of breaking a firing pin.
Five things can be done to the safety.
1. Leave it alone and use it when desired.
2. Replace it with an after market dummy that fills the hole and appears as a bolt.
3. Remove the stock. Turn in the safety set screw enough to lock the safety in the off position so that it can't be applied accidentally.
4. In a lathe, face off the left end of the safety so that it is flush with the left side of the receiver when in the off position. The safety can be applied by pushing on it with the end of a pencil.
5. Go to a hardware store and purchase an "O" ring or a "C" clip that fits the grove in the safety. Slip the "O" ring or "C" clip over the left end. This will prevent the safety from being applied accidentally.
REASSEMBLY
Reassemble the rifle in the reverse steps to disassembly. Put a light coat of oil on all parts prior to reassembly. Do not tighten any screw all the way until everything is back together. Then snug up all screws. Cycle the action several times to assure everything is working smoothly. If the trigger guard plate support screw is too tight, the action will appear sluggish. If this occurs on your rifle, back the screw off very slightly.

_________________
A cruel truth is much more desirable than a really nice lie.
'Tis far better to walk alone than to follow a crowd or an a**hole going the wrong way.


Last edited by 1895ss on Mon Mar 13, 2006 2:58 am; edited 8 times in total
Back to top
View user's profile Send e-mail
yotebuster
Member
Member


Joined: Oct 16, 2005
Posts: 216
Location: Georgia

PostPosted: Sun Mar 12, 2006 6:42 pm    Post subject: Re: Marlins trigger pull Reply with quote

1895SS, I would rather a professional do my action work. Any advice as to who to send my 1895 CB too for some work? By the way, great article on the how to! Thanks for your time.
Yotebuster Smile

_________________
May all your Bloodtrails be Vertical!
Back to top
View user's profile
1895ss
Super Member
Super Member


Joined: Jul 21, 2005
Posts: 2612
Location: Not Here...!!

PostPosted: Sun Mar 12, 2006 10:45 pm    Post subject: Re: Marlins trigger pull Reply with quote

Your welcome yotebuster, you would have to find a competent gun smith in your area. Smile

_________________
A cruel truth is much more desirable than a really nice lie.
'Tis far better to walk alone than to follow a crowd or an a**hole going the wrong way.
Back to top
View user's profile Send e-mail
ripper007
Member
Member


Joined: Mar 05, 2006
Posts: 199
Location: Colorado

PostPosted: Mon Mar 13, 2006 2:02 am    Post subject: Re: Marlins trigger pull Reply with quote

when I bought my Marlin 22 lever action. it had a back flip sight that was not working.
I called marlin, they sent me the whole assembly rear sight for free. no questions asked. and it was free shipping too.

that was the first time I have ever had no problems with a company.

thier support members was the best and was willing to help.

I am sure they will make your gun good.

my marlin 336c 30-30 has a fairly smooth triger on it. I do not know what pound pull it has but I know it is easy and smooth. I like it.
its not a hair trigger, but its good. I would say it is perffect for me.

I am sure marlin will agree that 10# pull is too much.

the only gun I have that I have to realy pull hard on the trigger is a old bolt action savage 22. I have never had to pull so hard on a trigger like this one. but other than that it is still a good accurate shootin gun. its like one of those guns you have to put up aim dead on and pull. do not think about it and do not stop to hold a aim on the target or it will almost be impossible to hit bullseye.

_________________
icq: 114244509
msn: kccrabb @ yahoo.com
Back to top
View user's profile ICQ Number MSN Messenger
Display posts from previous:   
Post new topic   Reply to topic   Printer Friendly Page    Forum Index » Gun & Firearm Discussions
Page 1 of 3
All times are GMT - 7 Hours
Go to page 1, 2, 3  Next



Jump to:  


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Valid CSS! Valid HTML 4.01!
Click to check if this page is realy HTML 4.01 compliant for speed :)

All logos and trademarks in this site are property of HuntingNut.com.
The comments are property of their posters, all the rest © 2011 by HuntingNut.com
Interactive software released under GNU GPL, Code Credits, Privacy Policy

.: Upgraded to DragonFly 9.2 by *Dizfunkshunal* :.