Coppermine Stats
Photo Albums
• Albums: 308
• Pictures: 2452 · Views: 825008 · Votes: 1316
· Comments: 86
|
Polishing a blackpowder rifle barrelDiscussions related to Guns and Firearms
View previous topic :: View next topic |
Author |
Message |
iowafarmboy Member
Joined: Mar 11, 2009 Posts: 109
|
Posted: Wed Feb 03, 2010 4:58 pm Post subject: Polishing a blackpowder rifle barrel |
|
I got a new Traditions barrel and receiver right before deer season. Now I have some time to play with it. The day after deer season I cleaning it. I was amazed that the barrel was full of rust the next day.
I read up some and used some metal polish I have for aluminum racing wheels. The results were dramatic to say the least. At least as to how the barrel looks. I haven't fired it yet as I'm waiting for the temperature to get above zero.
I have gone through the cycle 3 times so far. Using the 'course polish', cleaning, the fine polish, and deep cleaning. The barrel doesn't look any different after the first polishing, but every time I polish it again, the patches come back black as coal, so they are still polishing.
When I polished wheels, you polish until the black goes away. Will that happen here too, or am I wasting my time? The barrel loads all sabots hard except various EZ-load sabots, which I don't want to use. I have run a lead ball through the barrel and measured it. It's very close to .500 and pushing it down the barrel is pretty even, not like the old barrel that was very undersized within 8 inches of the breech.
|
|
Back to top |
|
|
slimjim Super Member
Joined: May 16, 2009 Posts: 8316 Location: Fort Worth TX
|
Posted: Wed Feb 03, 2010 7:51 pm Post subject: Re: Polishing a blackpowder rifle barrel |
|
I do not have personal experience with polishing a muzzle loader. I helped a friend gather information to work on his. Below is link that might have some good ideas for you. There is also information out there about coating the bore with telfon based lubricants after it clean and a cotton ball won't leave strands in your barre.. I'll keep looking for it. There is also Bore Coat.
Cleaning Muzzleloaders
Ultra Bore Coat
|
|
Back to top |
|
|
Crackshot Super Member
Joined: Oct 23, 2005 Posts: 1693 Location: Mich
|
Posted: Thu Feb 04, 2010 1:38 pm Post subject: Re: Polishing a blackpowder rifle barrel |
|
If its an aluminum cleaner, I cant see it doing you much good. Try useing a good valve lapping compound and a realy tight patch to LAP the bore, after cleaning it with very hot soapy water. Your aluminum "cleaner" is made for wheels and shiny places. Not a rifle bore. I fear you may be chemicaly stripping metal from the bore. Or at the very least causeing some molecular damage that could weaken the steel.
Just my 2 cents.
The only thing that touches my BP rifle bores for cleaning and what not are, Hot soapy water and 1000+ bore butter. And the occasional lapping compound. NEVER oil, Oil on the outside good! Oil on inside BAD!
_________________ The human mind is the weapon, the gun is just one of its tools. |
|
Back to top |
|
|
Pumpkinslinger Super Member
Joined: Sep 22, 2007 Posts: 5002 Location: NC foothills
|
Posted: Thu Feb 04, 2010 1:59 pm Post subject: Re: Polishing a blackpowder rifle barrel |
|
I've heard of using Flitz for polishing bores and tried it on a .22 Hornet. I couldn't really tell if it made much difference regarding cleaning. It didn't seem to have any negative effects though, I think my best groups came after the polishing. No major improvements though.
_________________ Mike
"I ain't no better than anybody else, and there ain't nobody better than me!" Ma Kettle |
|
Back to top |
|
|
chambered221 Super Member
Joined: Aug 17, 2007 Posts: 3455 Location: Lost for good !!!
|
Posted: Thu Feb 04, 2010 7:03 pm Post subject: Re: Polishing a blackpowder rifle barrel |
|
If you were to start with a shiny piece of steel and use a polishing or cutting compound you'll always get the black dirty look.
With aluminum it goes away because all your doing is removing any oxidization that present.
When dealing with rifle barrels you should use a non-embedding compound such as JB paste or bore cleaner.
There seems to be a 50/50 split as to even using these products in a rifle barrel.
If you use to much of a cutting compound it's possible to take away more metal than you want to leaving you with a over-sized bore.
If your using a product that will in-bed itself you take the chance of the bullets fire lapping the bore if your unable to completely remove it.
My advise is you should know what your doing before you do it !!!
_________________ Ask as many people needed, sooner or later your question will be answered the way you want it answered !!!
A free people ought not only to be armed and disciplined, but they should have sufficient arms and ammunition to maintain a status of independence from any who might attempt to abuse them, which would include their own government.
~George Washington |
|
Back to top |
|
|
PaulS Super Member
Joined: Feb 18, 2006 Posts: 4330 Location: South-Eastern Washington - the State
|
Posted: Fri Feb 05, 2010 1:32 am Post subject: Re: Polishing a blackpowder rifle barrel |
|
you guys with black powder guns need to use a cleaner made for black powder. My brother swears by this stuff and I have used it for gun oil for years with no problems. There is no need to put water down your bore with this:
Ed's Red:
"Ed's Red" Bore Cleaner
By Ed Harris Rev. 12-27-94
CONTENTS: Ed's Red Bore Cleaner
1 part Dexron II, IIe or III ATF, GM Spec. D-20265 or later.
1 part Kerosene - deodorized, K1
1 part Aliphatic Mineral Spirits, Fed. Spec. TT-T-2981F, CAS
#64741-49-9, or substitute "Stoddard Solvent", CAS #8052-41-3, or equivalent, (aka "Varsol")
1 part Acetone, CAS #67-64-1.
(Optional up to 1 lb. of Lanolin, Anhydrous, USP per gallon, OK to substitute Lanolin, Modified, Topical Lubricant, from the drug store)
MIXING INSTRUCTIONS:
Mix outdoors, in good ventilation. Use a clean 1 gallon metal, chemical-resistant, heavy gage PET or PVC plastic container. NFPA approved plastic gasoline storage containers are also OK. Do NOT use HDPE, which is breathable because the acetone will evaporate. The acetone in ER will attack HDPE in about 6 months, making a heck of a mess!
Add the ATF first. Use the empty container to measure the other components, so that it is thoroughly rinsed. If you incorporate the lanolin into the mixture, melt this carefully in a double boiler, taking precautions against fire. Pour the melted lanolin it into a larger container, rinsing the lanolin container with the bore cleaner mix, and stirring until it is all dissolved.
I recommend diverting a small quantity, up to 4 ozs. per quart of the 50-50 ATF/kerosene mix for use as an "ER-compatible" gun oil. This can be done without impairing the effectiveness of the mix.
INSTRUCTIONS FOR USE
1. Open the firearm action and ensure the bore is clear. Cleaning is most effective when done while the barrel is still warm to the touch from firing. Saturate a cotton patch with bore cleaner, wrap or impale on jag and push it through the bore from breech to muzzle. The patch should be a snug fit. Let the first patch fall off and do not pull it back into the bore.
2. Wet a second patch, and similarly start it into the bore from the breech, this time scrubbing from the throat area forward in 4-5" strokes and gradually advancing until the patch emerges out the muzzle. Waiting approximately 1 minute to let the bore cleaner soak will improve its action.
3. For pitted, heavily carbon-fouled "rattle battle" guns, leaded revolvers or neglected bores a bronze brush wet with bore cleaner may be used to remove stubborn deposits. This is unnecessary for smooth, target-grade barrels in routine use.
4. Use a final wet patch pushed straight through the bore to flush out loosened residue dissolved by Ed's Red. Let the patch fall off the jag without pulling it back into the bore. If you are finished firing, leaving the bore wet will protect it from rust for up to 30 days. If the lanolin is incorporated into the mixture, it will protect the firearm from rust for up to two years. For longer term storage I recommend use of Lee Liquid Alox as a Cosmolene substitute. "ER" will readily remove hardened Alox or Cosmolene.
5. Wipe spilled Ed's Red from exterior surfaces before storing the gun. While Ed's Red is harmless to blue and nickel finishes, the acetone it contains is harmful to most wood finishes).
6. Before firing again, push two dry patches through the bore and dry the chamber, using a patch wrapped around a suitably sized brush or jag. First shot point of impact usually will not be disturbed by Ed's Red if the bore is cleaned as described.
_________________ Paul
__________________
Speer, Lyman, Hodgdon, Sierra, and Hornady = reliable loading data
So and So's pages on the internet = NOT reliable loading data
Always check data against manuals
NEVER exceed maximum listed loads |
|
Back to top |
|
|
Aloysius Super Member
Joined: Nov 03, 2009 Posts: 2440 Location: B., Belgium
|
Posted: Fri Feb 05, 2010 1:47 am Post subject: Re: Polishing a blackpowder rifle barrel |
|
I have friends who run a patch with windowcleaner trough the bore right after shooting. They claim that the dirt remains soft and is easely removed afterwards at home with hot water (with a drop of disc cleaning soap added if you wish). Better don't use the wives' best cleaning bucket for this, because I discovered the hard way that it's easier to remove the blackpowder slam out of a barrel than out of a plastic bucket.
When you're not going to use the BP-rifle for a longer period, don't forget to oil the last patch with CLP-oil (or other oil that P-rotects) and just make the barrel dry right before next shooting.
For cleaning between the shots I use a drill cooling liquid. A friend who's using a Sharps and Browning breechloader in 45-70 and 45-120 uses what he calls a "fat-pill", about 1/4" bulletfat between the bullet and cardboard disc on top of the BP. He can shoot 30-40 times without cleaning his rifle.
So it seems that the best cleaning procedure starts with tricks to keep the dirt soft and protect against rust during and right after shooting.
It will make actual cleaning much easier afterwards.
And protect the bore after cleaning. Nobody likes a brown coloured patch when you want to use the rifle.
|
|
Back to top |
|
|
iowafarmboy Member
Joined: Mar 11, 2009 Posts: 109
|
Posted: Sun Feb 07, 2010 6:35 pm Post subject: Re: Polishing a blackpowder rifle barrel |
|
My polishing had the desired effect. The aluminum polish I use is FLITZ. The 'coarse' polish is Nuvite NuShine II grade F-7. I wasn't trying to make the bore bigger, I knew it was very close to the correct size. I was trying to get it so I could load a sabot without having to use some kind of lube. I don't have a gauge to measure how much it takes to load a round (Barnes 290 grain) but it feels just right now, not too easy and not too hard. I shot a 1 3/8 inch 3 shot group using 120 grains of Blackhorn powder not cleaning between rounds.... those were the 14th, 15th, and 16th bullets I shot today without cleaning. The other 13 bullets I shot were 250 grain as I was trying different loads to get the best accuracy should I use them.
After I did my polishing and cleaning, there was a noticeable difference in looking down the barrel. I didn't have too much to loose. When hunting it was impossible to load a 2nd round without bringing along a ton of stuff to clean and lube the barrel. Now all I need is powder, a bullet inside a sabot, and my loading rod. And I'm getting as good or better accuracy without all the cleaning and lubing steps. I'm satisfied.
I do appreciate the advice I got. I read several places on the correct steps to use and I guessed on what to use as polish. If the barrel diameter changed, it was less than a thou by my measurement.
|
|
Back to top |
|
|
gelandangan Super Member
Joined: May 07, 2006 Posts: 6401 Location: Sydney Australia
|
Posted: Sun Feb 07, 2010 8:40 pm Post subject: Re: Polishing a blackpowder rifle barrel |
|
Try polish then wipe with Lee Liquid Alox mixed 50-50 with mineral spirit..
Stop the rust pronto!.
_________________ A straight line is the shortest distance between two points.
A smile is the shortest distance between two people.
Do - Not try!
gelandangan.weebly.com/ |
|
Back to top |
|
|
hunterjoe21 Super Member
Joined: Mar 30, 2007 Posts: 1486 Location: Miles City, Montana
|
Posted: Sun Feb 07, 2010 10:49 pm Post subject: Re: Polishing a blackpowder rifle barrel |
|
iowafarmboy wrote: |
My polishing had the desired effect. The aluminum polish I use is FLITZ. The 'coarse' polish is Nuvite NuShine II grade F-7. I wasn't trying to make the bore bigger, I knew it was very close to the correct size. I was trying to get it so I could load a sabot without having to use some kind of lube. I don't have a gauge to measure how much it takes to load a round (Barnes 290 grain) but it feels just right now, not too easy and not too hard. I shot a 1 3/8 inch 3 shot group using 120 grains of Blackhorn powder not cleaning between rounds.... those were the 14th, 15th, and 16th bullets I shot today without cleaning. The other 13 bullets I shot were 250 grain as I was trying different loads to get the best accuracy should I use them.
After I did my polishing and cleaning, there was a noticeable difference in looking down the barrel. I didn't have too much to loose. When hunting it was impossible to load a 2nd round without bringing along a ton of stuff to clean and lube the barrel. Now all I need is powder, a bullet inside a sabot, and my loading rod. And I'm getting as good or better accuracy without all the cleaning and lubing steps. I'm satisfied.
I do appreciate the advice I got. I read several places on the correct steps to use and I guessed on what to use as polish. If the barrel diameter changed, it was less than a thou by my measurement. |
Holy Crap You've been through a lot with that gun.
_________________ My 1911 is more effective than your 911. |
|
Back to top |
|
|
iowafarmboy Member
Joined: Mar 11, 2009 Posts: 109
|
Posted: Mon Feb 08, 2010 7:48 pm Post subject: Re: Polishing a blackpowder rifle barrel |
|
Here is why I wanted to use the Barnes 290 grain bullet. For my rifle they have always flown as straight as I am able to shoot. One reason (I think) is that their sabots are so well built and designed that they allow the bullet to fly straight every time. I have a bag of found sabots and they all look like this. As you can see with the black sabots, some open fully and some loose a single petal (early?) and stray off course. So with the black sabots it's not unusual to have two almost touching then one 3 inches away or more.
The black sabots are supposedly made by the same company as the Barnes, but are a couple thou smaller in diameter to make them load easier. Before I polished my barrel they would not load without lube either. I don't like any of the EZ load sabots. So after polishing my barrel, I am now able to shoot either sabot without cleaning using Blackhorn powder.
The longer 290 grain bullet seems to fly slightly better in my barrel... 28 inch barrel and one in 28 twist. Is it the sabot? I'm no expert, but unless I really pull the trigger it's going to be in that 2 inch circle at 100 yards.
Description: |
I can't find every sabot as the snow is very deep. But I usually find one of these after I have a shot that strays.
|
Filesize: |
60.64 KB |
Viewed: |
8968 Time(s) |
|
Description: |
This is how they all 'should' look.
|
Filesize: |
65.69 KB |
Viewed: |
8968 Time(s) |
|
Description: |
'stock' Barnes sabot with 290 grain TMZ all copper bullet.
|
Filesize: |
50.08 KB |
Viewed: |
8968 Time(s) |
|
|
|
Back to top |
|
|
|
All times are GMT - 7 Hours
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You cannot attach files in this forum You can download files in this forum
|